Sexy Harness
Geometric Square Statement Earrings with Cut-Out Design
$8.26
Estimated Delivery Date: July 27-29
Color
Please select a color
Size
Please select a size
Discreet Shipping
Plain Packaging
No Content on Invoice
🚚 Discreet packaging — no brand name visible
⚡ Same day dispatch (orders before 2:00 PM)
🔒 256-bit SSL secure checkout
- SKU
- APBJ010-S1
- Weight
- 0.200
- Categories
- Earrings
Product Details
| Care Instructions | Wipe with dry cloth; avoid soaking; store flat in padded pouch |
| Lining | Not applicable — open cut-out construction |
| Closure | Standard silver-tone stud post with butterfly back |
| Material | Matte black acrylic or lightweight resin panel |
Related Searches
Frequently Asked Questions
Each earring drops approximately 5 cm from the post to the lowest point of the square frame. At that length they sit well below the earlobe and are clearly visible even with a chin-length bob, as long as the hair is tucked back or worn up.
The bars are cut from a single matte black acrylic or resin panel roughly 0.3 cm thick, so they hold their shape under normal handling. However, stacking them loose in a bag with heavier items risks bending the thin horizontal bars. Store flat in a pouch for best results.
These use a standard metal stud post with a butterfly back. They require a standard pierced ear hole (approximately 0.8 cm pin diameter) and are not available in a clip-on version.
The flat matte acrylic surface can show fine scratches if rubbed against abrasive materials. Wipe clean with a soft dry cloth rather than rough fabric, and store in a padded jewellery pouch to keep the surface looking sharp.
Product Detail
Black square drop earrings with a laser-cut striped cut-out pattern for bold minimalist style.
- ✓Matte black acrylic square frame, approximately 5 cm x 5 cm diagonal
- ✓Laser-cut striped cut-out pattern with four horizontal parallel bars
- ✓Lightweight construction: cut-out removes roughly 40 percent of panel mass
- ✓Standard 0.8 cm stud post, compatible with standard pierced ears only
- ✓Flat matte finish: no shine, no metallic sheen on the black body
- ✓Approximately 0.3 cm panel thickness for structured shape retention
- ✓Not suitable for clip-on or gauge piercings — fixed post only
These black geometric square drop earrings hang at roughly 5 cm diagonal and feature a laser-cut striped cut-out pattern inside a solid square frame, rotated 45 degrees so the flat edge faces down. The matte black finish gives the piece a sharp, high-contrast look without any shine or metallic distraction.
Cut-Out Detail and Shape
The interior of each earring is divided by four parallel horizontal bars running across the lower half of the diamond, creating open negative space above them. This striped cut-out design reduces weight significantly compared to a solid panel earring of the same size, so the 5 cm drops sit comfortably on the lobe without pulling.
- Diamond orientation: square rotated 45 degrees, point at top and bottom
- Cut-out pattern: four horizontal parallel bars across the lower section
- Frame width: approximately 0.5 cm solid border around the perimeter
- Drop length: approximately 5 cm from post to lowest point
- Small silver-tone post stud visible at the top attachment point
Styling and Occasion
The angular silhouette pairs well with structured necklines. Wear them with a sleeveless black top and tailored trousers for an office-to-evening transition, or with a strappy festival outfit where the matte black reads as an intentional graphic accent rather than an afterthought. The geometric shape also complements harness-style fashion accessories, echoing the angular hardware lines of a chest harness or body harness look.
- Festival outfit: crop top, high-waist shorts, black harness bra, these earrings
- Evening aesthetic: silk cami, minimal jewellery, these as the single statement piece
- Party look: off-shoulder dress, updo hairstyle to showcase the full 5 cm drop
Sizing and Fit
Each earring measures approximately 5 cm x 5 cm at its widest diagonal points. The post is a standard 0.8 cm stud pin suitable for standard pierced ears. Because the cut-out design removes roughly 40 percent of the surface area, the earring weighs noticeably less than a solid panel of equivalent dimensions — estimated at under 8 g per piece. Not suited for stretched or gauge piercings, and the fixed post means these are not adjustable for clip-on wear.
Material and Care
The earrings appear to be constructed from matte black acrylic or lightweight resin, giving the consistent flat-black colour across the entire frame and bars. The surface is smooth and non-porous. To clean, wipe with a dry or slightly damp cloth — avoid prolonged water exposure to protect the post fitting. Store flat or in a padded jewellery pouch to prevent the thin bars from bending under pressure.
- Material: matte black acrylic or resin panel, approximately 0.3 cm thick
- Finish: flat matte, non-reflective black
- Post: silver-tone metal stud pin
- Care: dry cloth wipe, avoid soaking, store flat
Best Seller Belts
Geometric Square Statement Earrings with Cut-Out Design
$8.26
